Pièce
Carte son de type 1.pdf · 11 358 mots · du marché « Transformation du Musée de la Carte à Jouer - travaux de rénovation et agencement intérieur sur 18 lots (gros-œuvre,… », dossier de consultation officiel.
D01247020A
US-16x08
USB2.0 Audio Interface/Mic Preamp
Reference Manual
Before connecting this unit to a computer, you must download and install a dedicated driver.
Contents
1 – Introduction...............................................3 Windows 8.....................................................................23
Features................................................................................... 3 Windows 7.....................................................................23
Conventions used in this manual. ................................. 3 Mac OS X and iTunes. .......................................................24
iOS...........................................................................................24
2 – Names and functions of parts...................4
Front panel............................................................................. 4 9 – MIDI Implementation Chart....................25
Rear panel. ............................................................................. 5
10 – Troubleshooting....................................26
3 – Installation.................................................6 Troubleshooting. ...............................................................26
System requirements......................................................... 6
11 – Specifications.........................................28
Windows. ......................................................................... 6
Specifications......................................................................28
Mac OS X.......................................................................... 6
Ratings............................................................................28
iOS devices...................................................................... 6
Analog inputs...............................................................28
Supported audio drivers............................................ 6
Analog outputs. ..........................................................28
Installing the driver and Settings Panel. ..................... 6
Control input/output ratings..................................28
Installing the driver and Settings Panel for
Windows. ......................................................................... 6 Audio performance....................................................29
Installing the Mac OS X Settings Panel. ................ 7 Computer system requirements..................................29
Uninstalling the driver and Settings Panel.......... 9 Windows. .......................................................................29
Automatic launching of the Settings Panel. ....... 9 Mac OS X........................................................................29
iOS devices....................................................................29
4 – Preparation. .............................................10 Supported audio drivers..........................................29
Attaching the rackmount angles.................................10 General..................................................................................29
Connecting the power. ...................................................10 Dimensional drawings.....................................................30
Block diagrams. ..................................................................31
5 – Connections. ............................................ 11
Level diagrams. ..................................................................32
Examples of connections with other equipment. . 11
Computer connections. ..................................................12
Audio connections............................................................12
Microphones. ...............................................................12
Guitar. .............................................................................12
Electronic and audio devices and other
equipment. ...................................................................12
Analog record players...............................................12
Monitor speakers. .......................................................12
Headphones. ................................................................12
MIDI connections. .............................................................12
Connecting with iOS devices. .......................................12
6 – Using the Settings Panel.........................13
Opening the Settings Panel...........................................13
Settings Panel screen.......................................................13
MIXER page..........................................................................14
INTERFACE page.................................................................17
OUTPUT SETTING page. ..................................................18
Settings Panel pull-down menus. ...............................19
View menu. ...................................................................19
SceneMemory menu.................................................20
7 – Mic Preamp Mode....................................22
Using the unit as a standalone mic preamp. ...........22
8 – Application Guide....................................23
Windows Media Player. ...................................................23
2 TASCAM US-16x08
1 – Introduction
Features Conventions used in this manual
• Built-in Ultra-HDDA mic preamps with discrete construction The following conventions are used in this manual.
that achieves −125dBu EIN • Switches, connectors and other physical parts of this unit
• Support for direct guitar input are written using a bold font like this: PHONES knob.
• Input specifications that can handle the sound pressures of • Information shown on the computer display is written like
drum recording easily this “OK”.
• 8 XLR inputs that support +48V phantom power and 6 TRS • As necessary, additional information is provided under TIP,
inputs that can be switched between −10 dBV and +4 dBu NOTE and CAUTION headings.
• Standalone mic preamp use also supported
TIP
• Support for high resolution recording formats up to
24-bit/96kHz These are tips about how to use the unit.
• USB 2.0 computer connection NOTE
• Advanced DSP mixer with four-band equalizer and These provide additional explanations and describe special
compressor on each channel cases.
• Driver software that can be installed without connecting
the unit CAUTION
• Angled design provides excellent usability on a desktop Failure to follow these instructions could result in injury,
• Tough metal casing can endure even hard use damage to equipment or lost recording data, for example.
• Separate controls for line and headphones output volumes
• Supports connection with an iPad or other iOS device
• Operation confirmed with major DAW software (Sonar,
ProTools, Cubase, Live, Studio One, GarageBand)
• MIDI input and output enable connection with keyboards
and other MIDI devices
• Rack mount adapters and hex key included
• Support for Windows and Mac
• High 56dB input level range supports dynamic mic input
• Balanced analog TRS output jacks suitable for connection to
powered monitors
• Standard stereo TRS headphones jack with 70mW per
channel output
• Low latency monitoring through the DSP mixer
• Patch bay allows outputs to be assigned freely
• Scene memories can store DSP mixer settings (up to 10
scenes can be stored and renamed)
• 8 balanced analog TRS output jacks
• AC adapter included
Note about computer operation
If you are unsure about anything related to the basic operation
of a computer when it is mentioned in an explanation in this
manual, please refer to the computer operation manual.
This product incorporates a Blackfin® processor made by
Analog Devices, Inc.
TASCAM US-16x08 3
2 – Names and functions of parts
Front panel
1 STANDBY/ON switch and indicator 4 IN 9-10 (balanced/unbalanced) jacks and LINE/INST
Press to turn the unit on and to put it into standby. The switches
STANDBY/ON indicator lights green when the unit is on. These are standard analog TRS input jacks.
The LINE/INST switches enable support for both line
2 Phantom power switches
input, including audio equipment and keyboards, and high
Use these switches to provide +48V phantom power to the
impedance input, including direct input of guitars.
IN 1–4 and IN 5–8 jacks.
You can adjust their input gains with the gain knobs.
These switches each turn phantom power on/off for 4
channels at a time. Phantom power is supplied when a (Tip: HOT, Ring: COLD, Sleeve: GND)
switch is set to +48V.
5 Gain knobs and overload indicators
CAUTION Use the 1–10 gain knobs to adjust the gain of IN 1-10
• Before using these switches to turn phantom power on independently.
(+48V) or OFF, set the PHONES and LINE OUT 1-2 knobs These can set the gain for IN 1-8 between −12 dBu and −68
to their minimum values. Failure to do so could cause a loud dBu and for IN 9-10 between +4 dBu and −42 dBu (between
noise that might damage other equipment or harm people. −12 dBV and −57 dBV during guitar input).
• Do not connect or disconnect mics when a switch is set to The overload indicators to the upper left of each of the 1–10
+48V. gain knobs light just before an input is about to distort
• Do not supply phantom power to an unbalanced dynamic (when the signal exceeds −1 dBFS).
mic. 6 LINE OUT 1-2 knob
• Supplying phantom power to some ribbon mics will break Use this knob to adjust the output level of the LINE OUT 1-2
them. If you are unsure, do not supply phantom power to a jacks on the back of the unit.
ribbon mic.
7 PHONES jack and knob
3 IN 1-8 (BALANCED) jacks Use this standard stereo jack to connect stereo headphones.
These are analog XLR input jacks. You can adjust their input The sound output is the same as the signals output from the
gains with the gain knobs. LINE OUT 1-2 jacks.
(1: GND, 2: HOT, 3: COLD) Use the PHONES knob to adjust the headphone output
level.
8 USB indicator
This lights orange when the USB connection is working.
CAUTION
Before connecting headphones, minimize the volume with
the PHONES knob. Failure to do so might cause sudden loud
noises, which could harm your hearing or result in other
trouble.
4 TASCAM US-16x08
2 – Names and functions of parts
Rear panel
9 USB port e Cord holder
Use the included USB cable to connect the unit to a Attach the cord of the included AC adapter here to prevent
computer or iOS device (supports USB 2.0). the plug from becoming disconnected.
CAUTION r LINE OUT 1-8 (balanced) jacks
• USB 1.1 is not supported. These are standard TRS analog line output jacks. Their
nominal output levels are +4 dBu.
• When connected to a USB 3.0 port, it will function in High
Speed mode equivalent to USB 2.0 (480 Mbps maximum). (Tip: HOT, Ring: COLD, Sleeve: GND)
0 MIDI OUT connector t AUTO POWER SAVE switch
This 5-pin DIN is a standard MIDI output connector. This can be set to have the unit turn itself off (start standby)
automatically if no input signal (above −60 dBFS) has been
This outputs MIDI signals. detected for 30 minutes when operating in mic preamp
q MIDI IN connector mode.
This 5-pin DIN is a standard MIDI input connector. CAUTION
Use this to input MIDI signals. If you want to turn the unit on again after it has turned itself
w LINE IN 11-16 (balanced) jacks and switches off (entered standby) automatically using this function, set
These are standard TRS line input jacks. Use the LEVEL the STANDBY/ON switch to STANDBY once, wait at least 8
switches to set the nominal level to −10 dBV or +4 dBu. seconds and then set it to ON again.
(Tip: HOT, Ring: COLD, Sleeve: GND) y DC IN 12V connector
Connect the included AC adapter (GPE248-120200-Z) here.
NOTE
The input gain cannot be adjusted for these jacks.
TASCAM US-16x08 5
3 – Installation
System requirements Supported audio drivers
Windows: ASIO2.0, WDM, MIDI
Check the TEAC Global Site (http://teac-global.com/) for the
Mac: Core Audio, Core MIDI
latest information about supported operating systems.
Windows Installing the driver and Settings
Panel
88 Supported operating systems
Windows 8 (including 8.1) 32-bit To use this unit with a Windows computer, a driver and Settings
Windows 8 (including 8.1) 64-bit Panel must be installed on it. To use this unit with a Mac, a driver
does not need to be installed, but the Settings Panel must be
Windows 7 32-bit SP1 or later installed in order to use the DSP mixer functions.
Windows 7 64-bit SP1 or later Download the latest driver and Settings Panel for the operating
88 Computer hardware requirements system you are using from the TEAC Global Site (http://
teac-global.com/).
Windows computer with a USB 2.0 or USB 3.0 port iiWhen you install the driver on a Windows computer, the
88 CPU/processor speed Settings Panel will be installed at the same time.
iiOnly the Settings Panel needs to be installed on a Mac. This
2 GHz or faster dual core processor (x86)
unit can be operated with the standard Mac OS driver, so
88 Memory there is no need to install a driver.
2 GB or more iiWhen using this unit with an iOS device, the standard OS
driver will be used, so there is no need to install a driver or
88 Display resolution Settings Panel.
Display with 1280x800 resolution CAUTION
CAUTION Restarting the computer might be necessary after instal-
lation or uninstallation completes. Save your data and
Operation of this unit was confirmed using standard conduct other necessary steps in other applications before
computers that meet the above requirements. This does quitting them.
not guarantee operation with all computers that meet the
above requirements. Even computers that meet the same
system requirements might have processing capabilities Installing the driver and Settings Panel for
that differ according to their settings and other operating
conditions Windows
NOTE NOTE
If noise occurs, please set your computer’s power options to iiComplete installation of the driver on the computer before
“High Performance”. connecting the unit to it with the USB cable. If you already
connected the unit using the USB cable before installing the
driver, and the Found New Hardware Wizard launched on the
Mac OS X computer, close the Wizard and disconnect the USB cable.
88 Supported operating systems 88 Installation procedures
OS X Yosemite (10.10 or later) 1. Download the latest driver for the operating system you are
using from the TEAC Global Site (http://teac-global.com/)
OS X Mavericks (10.9.1 or later) and save it on the computer to be used with the unit.
OS X Mountain Lion (10.8.4 or later) 2. Open the saved driver (zip file) on, for example, the
88 Computer hardware requirements computer desktop.
3. Double-click the “US-16x08_Installer.exe” file in the folder
Apple Mac computer with a USB 2.0 or USB 3.0 port
that appears after uncompression to automatically launch
88 CPU/processor speed the installation software.
2 GHz or faster dual core processor CAUTION
88 Memory If you open a zip file without decompressing it and double-
click the “US-16x08_Installer.exe” file in the folder that
2 GB or more opens, installation will not start. Right-click the zip file and
88 Display resolution select “Extract All", for example, to decompress it and then
try again.
Display with at least 1280x800 resolution 4. When a “Security Warning” or “User Account Control” screens
appear, click the “Yes” button.
iOS devices
Apple devices running iOS 7 or later
6 TASCAM US-16x08
3 – Installation
5. Next, select a language and click the “OK” button. 11. Click the “Finish” button when the screen below appears.
6. When the Setup Wizard screen appears, click the “Next”
button.
12. The following screen appears when installation has
completed. Click the “Finish (F)” button.
7. Read the contents of the License Agreement, and select
“Agree (A)” if you agree to the terms. Then, click the “Next”
button.
The installer will quit and the Settings Panel will launch.
CAUTION
• When installing the driver, a warning might appear with a
message such as, “The software you are installing for the
hardware has not passed Windows Logo testing to verify its
compatibility with Windows.” If this message appears, click
“Continue Anyway” to proceed with the installation.
Installing the Mac OS X Settings Panel
8. Next, click the “Install (I)” button.
NOTE
• Install the Settings Panel on the computer before
connecting the unit to it with the USB cable. If the unit is
connected by the USB cable, cancel driver installation and
disconnect it before starting driver installation again.
• During Settings Panel installation a warning message
like this might appear: “US-16x08.pkg can't be opened
because it was not downloaded from the Mac App Store.”
If a message like this appears, follow the instructions in
“Working with Gatekeeper” on page 8 in this manual
and then proceed with the installation.
9. When the Install Wizard screen appears, click the “Next (N)”
button. 88 Installation procedures
1. Download the latest Settings Panel for the operating system
you are using from the TEAC Global Site (http://teac-global.
com/) and save it on the computer to be used with the unit.
2. Double-click “US-16x08_X.XX.dmg", which is the saved disk
image file for the Settings Panel, and double-click “US-16x08.
pkg” inside the folder that opens.
NOTE
10. Next, click the “Install (I)” button to start installation. Depending on the computer’s settings, the downloaded zip
file might not have opened automatically. In this case, open
the zip file first and then double-click the disk image file.
TASCAM US-16x08 7
3 – Installation
3. When the installer starts, click the “Continue” button. 88 Working with Gatekeeper
When using Mac OS X, depending on the Gatekeeper security
function setting, a warning message might appear during
installation.
Resolution depends on the warning message shown.
See the following explanations for details.
When the Gatekeeper setting is “Allow applications
downloaded from: the Mac App Store"
The following security warning might be shown: “'US-16x08.
pkg' can't be opened because it was not downloaded from
4. Next, select the desired language and click the “Continue” the Mac App Store."
button.
In this case, click the OK button to close the message. Then,
control-click (or right-click) the file and click “Open”.
Click the “Open” button if the following security warning
message appears: “'US-16x08.pkg' can't be opened because
5. Click the “Read License” button and check the contents it was not downloaded from the Mac App Store. Are you
of the Software License Agreement. If you agree to the sure you want to open it?"
contents of the license, click “Agree”.
Then, click the “Next” button.
This message might also appear when the Gatekeeper
setting is something other than “Allow applications
downloaded from: the Mac App Store"
The security warning message “'US-16x08.pkg' can't be
opened because it was not downloaded from the Mac App
6. Next, click the “Install” button to start installation. Store.” could appear again, and you might not be able to
open the file.
In this case, copy the file from the folder where it is to the
desktop or another folder, and then open it. Alternatively,
7. The following screen appears when installation has change the Gatekeeper settings to “Allow applications
completed. Click the “Close” button. downloaded from: the Mac App Store and identified devel-
opers” and try opening it again.
The Settings Panel will launch.
8 TASCAM US-16x08
3 – Installation
Changing the Gatekeeper setting Automatic launching of the Settings Panel
The Gatekeeper setting can be changed using the “Allow
applications downloaded from:” item on the “General” page The Settings Panel will automatically launch when the computer
of the “Security & Privacy” pane of the System Preferences. starts up.
To change this, you must click the lock icon ( ) at the This allows the Settings Panel to apply its parameter settings,
bottom left and enter a password to unlock the settings. for example, to the unit. If you use this unit without starting the
Settings Panel, the unit will use the default Settings Panel values
for parameters. (For information about the default values of the
Settings Panel, see “Initializing the Settings Panel settings” on
page 19.)
If you do not want the Settings Panel to launch automatically
when the computer is started, follow these procedures.
NOTE
• The automatic launching setting for the Settings Panel
applies only to the user account that was logged in when it
was installed.
This setting will lock again when you click the “Show All” • The Settings Panel cannot be used on an iPad or other iOS
button at the top left of the window to close the open pane device.
or when you quit the System Preferences by, for example,
Windows OS
clicking the round button at the top left corner of the
window ( ) or typing command-Q. Windows 8
1. Right-click the Start screen to show the App Bar. In
CAUTION Windows 8, right-click the Start screen and click the “All
Changing the Gatekeeper settings could result in security apps” button (or the ¡ â button at the bottom left of the
risks. screen in Windows 8.1), and click “Task Manager” to open
it.
If you changed the Gatekeeper setting to decrease security
(use one of the lower settings), set it back to the original 2. Right-click “US-16x08” in the “Start-Up” tab and select
setting after updating the driver and/or firmware. “Disable” from the menu.
NOTE
Uninstalling the driver and Settings Panel If you want to enable automatic launching of the Settings
Panel again, right-click “US-16x08” and select “Enable”
NOTE from the menu.
Normally, there is no need to uninstall the driver or Settings Windows 7
Panel. Follow these procedures if a problem occurs or you no Click the Start button, select All Programs and then
longer intend to use the unit with the computer. Startup. Right-click “US-16x08” and select “Delete” from
the menu.
88 Windows
Uninstall from the “Programs and Features” Control Panel. NOTE
1. From the Start menu, open the Control Panel, and then If you want to enable automatic launching of the Settings
Programs and Features. Panel again, add a shortcut for “US-16x08” to the Startup
menu.
NOTE
Mac OS X
In Windows 8, to open the Control Panel, right-click the Open the System Preferences app and open the Users &
Start screen and click the “All apps” button (or click the ¡ â
Groups pane. Click Login Items, select “US-16x08_Setting-
button that appears at the bottom left of the Start screen in sPanel” and click the − button.
Windows 8.1), then click “Control Panel” on the Apps screen.
2. If “View by:” is set to “Category", click “Uninstall a program”
under the “Program” item.
If “View by:” is set to “Large icons” or “Small icons", click
“Programs and Features”.
3. Double-click “TASCAM US-16x08 version X.XX” ("X.XX” is the
driver version) in the list.
4. Then, follow the instructions that appear on the screen.
88 Mac OS X
Delete the “US-16x08” application from the Application folder to
complete uninstallation.
NOTE
If you want to enable automatic launching of the Settings
Panel again, click the + button and select “US-16x08_
SettingsPanel”.
TASCAM US-16x08 9
4 – Preparation
In order to prevent the cord from becoming disconnected
Attaching the rackmount angles during use, always wrap the cord around the cord holder when
connecting it.
In order to mount this unit in a rack, you must remove the
frames and install the included rackmount angles. Follow these
procedures to change them.
(You will need a flat-bladed screwdriver.)
1. Use the hex key included with this product to remove the
four screws on each side from the positions shown below.
CAUTION
• Always use the AC adapter (GPE248-120200-Z) that was
shipped with the unit. Using a different AC adapter could
2. Remove the frames from both sides of the unit cause malfunction, overheating, fire or other problems.
3. Attach the included rackmount angles using the rackmount • The AC adapter for this unit includes two types of outlet
angle attachment screws and the Phillips screwdriver that plugs. Attach the type of plug that matches the power outlet
you prepared. that you are using.
88 Changing the outlet plug
3
2 $ 5 %
1 4
4. Reverse these procedures to reinstall the frame pieces origi- 1. Move the latch on the AC adapter in the direction of the
nally attached to the unit. arrow.
2. Pull off the outlet plug.
3. Replace it with the other outlet plug (A or B).
Connecting the power 4. Move the latch on the AC adapter in the direction of the
arrow again.
Use the included AC adapter to connect a power supply to the
unit as shown below. 5. Attach the outlet plug to the AC adapter.
This completes changing the outlet plug.
After changing the outlet plug, confirm that it is not loose
Power outlet or crooked and that everything is normal before plugging it
into an outlet.
GPE248-120200-Z (included) DC plug
CAUTION
Do not use the adapter if there is anything abnormal about
the plug after changing it. Use when the plug is abnormal
could cause fire or electric shock. Contact the retailer where
you purchased the unit or a TEAC service center (on the back
cover) to request repair.
10 TASCAM US-16x08
5 – Connections
Examples of connections with other equipment
Drums Guitar
Bass Guitar
Vocal mics
Headphones
Sound module
Keyboard
USB
Powered speakers or
amplifier and speakers
Drum machine
Computer
CAUTION
• Before making connections, turn this unit and all equipment to be connected off (standby).
• The phantom power switches change the settings for groups of 4 channels. Do not set phantom power to +48V when an unbalanced
dynamic mic is connected.
• Do not connect or disconnect mics while phantom power is set to +48V. Doing so could cause a loud noise and might damage this
unit and connected equipment.
• Set the LINE OUT and PHONES knobs to their minimum values before switching the phantom power setting between +48V and OFF.
Sudden loud noises from monitoring equipment could occur, and this could damage the equipment or harm hearing.
• Supplying phantom power to some ribbon mics will break them. If you are unsure, do not supply phantom power to a ribbon mic.
TASCAM US-16x08 11
5 – Connections
Computer connections Guitar
When connecting a guitar or bass guitar directly to this unit, use
Use the included USB cable to connect the unit to a computer the IN 9 or IN 10 jack on the front of the unit and set the LINE/
USB 2.0/3.0 port. When the USB connection is working, the USB INST switch for that jack to INST.
indicator on the front of the unit lights.
CAUTION Electronic and audio devices and other
• If you connect this unit to a computer via a USB hub, for
equipment
example, audio signal dropouts, clicking noises and other
interference could occur due to the influence of other USB When connecting an electronic instrument or other audio
devices connected to that hub. For this reason, we strongly equipment directly to this unit, use the IN 9-10 jacks on the
recommend connecting this unit to a separate USB port. front of the unit or the IN 11-16 jacks on the back and set the
Connecting USB keyboards and mice, however, to the same LINE/INST switches for those jacks to LINE.
bus should not be a problem.
Analog record players
Audio connections The output of an analog record player cannot be connected
directly to this unit. To connect an analog record player to this
Analog audio signals input into this device from mics, guitars, unit, a phono amp and equalizer (or an audio amplifier that has
keyboards and other audio equipment can be converted into phono input jacks) must be connected between them.
digital signals and transmitted to the computer via USB. In
addition, by connecting speakers (through an amplifier if not
powered) or headphones to this unit, you can monitor audio Monitor speakers
signals that are input to this unit and output from the computer.
Connect monitor speakers (powered speakers or an amplifier
CAUTION and speaker system) to the LINE OUT 1-2 jacks on the back of
Before connecting audio equipment, set the unit’s 1-10 the unit.
gain, LINE OUT 1-2 and PHONES knobs to their lowest Use the LINE OUT 1-2 knob on the front of the unit to adjust the
values. Failure to do so could cause sudden loud noises speaker volume.
from monitoring equipment, and this could damage the
equipment or harm hearing.
Headphones
Connect headphones to the PHONES jack (standard stereo) on
Microphones the front of the unit.
• Dynamic mics
CAUTION
Connect mics to the IN 1-10 jacks on the front of the unit.
• Condenser mics Before connecting headphones, minimize the volume with
the PHONES knob. Failure to do so might cause sudden loud
When using condenser mics that require phantom power, noises, which could harm your hearing or result in other
connect them to the IN 1-8 jacks, and set the phantom trouble.
power switches to +48V.
CAUTION MIDI connections
• Before making connections, turn this unit and all equipment
to be connected off (standby). Connect sound modules, keyboards, synthesizers, drum
• Do not connect or disconnect mics while phantom power is machines and other MIDI devices to the unit in the following
set to +48V. Doing so could cause a loud noise and might manner.
damage this unit and connected equipment. • If you want to monitor sound from a MIDI device, connect its
• Set the LINE OUT and PHONES knobs to their minimum outputs to this unit's IN 9-16 jacks or use an external mixer.
values before switching the phantom power setting • You can also use the MIDI IN and MIDI OUT connectors
between +48V and OFF. Sudden loud noises from on the back of the unit to send and receive MIDI timecode
monitoring equipment could occur, and this could damage (MTC). By doing this, you can use an application that
the equipment or harm hearing. supports MTC to synchronize a multitrack recorder (MTR)
• Supplying phantom power to some ribbon mics will break and MIDI devices.
them. If you are unsure, do not supply phantom power to a
ribbon mic. CAUTION
When using Windows Media Player, if the “Sound and Audio
Devices Properties” Control Panel “MIDI music playback
(default device)” is set to “Microsoft GS Wavetable SW
Synth", you will not be able to hear MIDI performances
through this unit's LINE OUT 1-8 or PHONES jacks.
Connecting with iOS devices
A Lightning to USB Adapter is required.
You will need to prepare an Apple genuine Lightning to USB
Adapter (sold separately).
12 TASCAM US-16x08
6 – Using the Settings Panel
You can use the Settings Panel to change and save settings for
the various functions of the unit. Settings Panel screen
The Settings Panel has three tabbed pages.
Opening the Settings Panel Click a tab at the top of the Settings Panel to open that page.
MIXER: Make built-in mixer and effects settings on this page.
Launch the Settings Panel installed on the computer to show it INTERFACE: This page shows the current status of the driver
on the computer display. and information about connections. It also allows you to
Open the Settings Panel in the following ways. change various settings (Windows only).
OUTPUT SETTING: Make settings for each output on this
NOTE
page.
The Settings Panel cannot be used on an iPad or other iOS
device. CAUTION
• When you open the Settings Panel, it will have the same
88 Windows OS
state as when it was last closed, but the settings data is
• Select the Settings Panel from “All Programs” or “All apps" not saved automatically. To save the settings of every
Windows 8 page (MIXER, INTERFACE and OUTPUT SETTING), use the
In Windows 8, right-click the Start screen and click the “All Scene Memory menu in the menu bar. See “Settings Panel
apps” button (in Windows 8.1, the ¡ â button that appears pull-down menus” on page 19 in this manual.
at the bottom left of the Start screen) to open the Apps • The signals input through each of the 16 channels are trans-
screen. On this screen, click the “US-16x08 Settings Panel” mitted to the computer without being affected by SOLO,
item under “TASCAM” to open the Settings Panel. MUTE, PAN, and fader settings. For this reason, fader and
Windows 7 pan changes made in the Settings Panel will not alter the
signals sent to a DAW on the same computer.
Start button w All Programs w select “US-16x08
Settings Panel” under TASCAM to open the Settings Panel. For details, see “Block diagrams” on page 31.
• In Windows 8, select “US-16x08 Settings Panel” on the Start
screen to open the Settings Panel.
NOTE
In Windows 8.1, the application is not automatically added
to the Start screen.
• Open the Settings Panel from the Control Panel.
Windows 8
1. In Windows 8, right-click the Start screen and click
the “All apps” button (or s button that appears at the
bottom left of the Start screen in Windows 8.1), and
click “Control Panel” to open it.
2. If the Control Panel is showing categories, set the “View
by:” item to “Large icons” or “Small icons”.
3. Select “US-16x08 Settings Panel” to open the Settings
Panel.
Windows 7
1. Click the Start button and select “Control Panel” to
open the Control Panel.
2. If the Control Panel is showing categories, set the “View
by:” item to “Large icons” or “Small icons”.
3. Select “US-16x08 Settings Panel” to open the Settings
Panel.
NOTE
In Windows 8, you can also open the Control Panel by
clicking the Control Panel item in the menu that appears if
you right-click the bottom left corner of the desktop.
88 Mac OS X
• Using the Finder, open the Applications folder and click
“US-16x08_SettingsPanel” to open the Settings Panel.
• In the Audio Devices window of the Audio MIDI Setup
application, right-click (control-click) “US-16x08” (or click
the settings icon when the unit name is selected) and click
“Configure device…” to open the Settings Panel.
TASCAM US-16x08 13
6 – Using the Settings Panel
MIXER page
1 2
3
45
6
7
8
9
0
q
w
Windows Settings Panel screen
NOTE the less acute it becomes, making it affect a broader
On a Mac, “View” and “SceneMemory” appear in the menu frequency band.
bar at the top of the screen. For details, see “Settings Panel Range: 0.25 – 16.00 (default: 1.00)
pull-down menus” on page 19. LOW MID GAIN knob
Sets the amount the level is increased or decreased for
the LOW MID band.
1 EQUALIZER (4-band parametric EQ)
Use the equalizer to increase or decrease the levels of Range: ±12 dB (default: 0 dB)
specific frequency ranges. This can be used, for example, LOW MID FREQ knob
to enhance the sound of individual instruments, to adjust Sets the center frequency of the LOW MID band.
the balance of a wide frequency range and to cut specific
unwanted frequencies. Range: 32 Hz – 18.0 kHz (default: 300 Hz)
The frequency response with the current settings is shown LOW MID Q knob
as a graph even when the equalizer is off. Sets the acuteness of the peak of the LOW MID band.
The equalizer has a high-shelf HIGH band, a low-shelf LOW The higher the value the more acute it becomes, making
band and peaking (bell-shaped) HIGH MID and LOW MID it affect a narrower frequency band. The lower the value,
bands. the less acute it becomes, making it affect a broader
HIGH GAIN knob frequency band.
Sets the amount the level is increased or decreased for Range: 0.25 – 16.00 (default: 1.00)
the HIGH band. LOW GAIN knob
Range: ±12 dB (default: 0 dB) Sets the amount the level is increased or decreased for
HIGH FREQ knob the LOW band.
Sets the cutoff frequency of the HIGH band. Range: ±12 dB (default: 0 dB)
Range: 1.7 kHz – 18.0 kHz (default: 5.0 kHz) LOW FREQ knob
HIGH MID GAIN knob Sets the cutoff frequency of the LOW band.
Sets the amount the level is increased or decreased for Range: 32 Hz – 1.6 kHz (default: 80 Hz)
the HIGH MID band. LCF button
Range: ±12 dB (default: 0 dB) Turn the LCF button on to enable the low-cut filter, which
HIGH MID FREQ knob cuts noise and other sounds at low frequencies.
Sets the center frequency of the HIGH MID band. Off (default): LCF button unlit
Range: 32 Hz – 18.0 kHz (default: 1.2 kHz) On: LCF button lit
HIGH MID Q knob To set the equalizer for a channel, select its Analog X button
Sets the acuteness of the peak of the HIGH MID band. (3).
The higher the value the more acute it becomes, making The equalizer settings will be shown for the channel selected
it affect a narrower frequency band. The lower the value, by its Analog X button (3).
14 TASCAM US-16x08
6 – Using the Settings Panel
2 COMPRESSOR 4 PHASE buttons
When the input volume exceeds the THRESHOLD level, Turn a PHASE button on to reverse the phase of that
the input volume is compressed, reducing output volume channel.
variation.
5 EQ buttons
For example, by reducing the high level parts of sounds
Turn an EQ button on to enable the equalizer on that
as they occur, a more even volume level throughout can
channel.
be achieved. This allows lower-level sounds to be raised,
resulting in a fuller sound. 6 COMP buttons
Three meters show the level of the signal input to the Turn a COMP button on to enable the compressor on that
compressor (INPUT), the level of the signal output from the channel.
compressor (OUTPUT) and the gain reduction caused by the
compressor (GR). 7 SOLO buttons
Turn a SOLO button on to solo that channel.
THRESHOLD knob
With this unit, when the SOLO button of a channel is
Sets the threshold level that will cause the effect to start.
enabled, all other channels are automatically muted (solo-in-
Range: −32 dB – 0 dB (default: 0 dB) place monitoring).
RATIO knob The MUTE buttons for channels that are muted will light.
Sets the compression ratio for the input volume. (Default: off )
Turning it right raises the compression ratio, increasing Multiple channels can be soloed at the same time.
the amount of compression.
Range: 1.0:1 – inf:1 (default: 1.0:1) NOTE
• When all the SOLO buttons are off, clicking the SOLO
GAIN knob
button of one channel will put the unit into solo mode and
Sets the gain of the output signal.
automatically mute the other channels, lighting their MUTE
When the volume is compressed, the output level buttons.
becomes lower than the input level. Use the GAIN knob • When all SOLO buttons are disabled, channels that had
to increase the output level so that it is close to the input
been automatically muted will become unmuted. Channels
level.
that had been individually muted before the unit entered
Range: 0 dB – 20 dB (default: 0 dB) solo mode will remain muted.
ATTACK knob • The MASTER L/R channel MUTE button will not turn on
Sets the amount of time until the compression reaches automatically when the unit enters solo mode.
the compression RATIO setting after the input volume
exceeds the threshold. 8 MUTE buttons
Turn a MUTE button on to mute that channel.
Range: 2 ms – 200 ms (default: 2 ms)
(Default: off )
RELEASE knob
Sets the amount of time until the compression stops and NOTE
the sound returns to its uncompressed level after the In addition to turning the MUTE button on and off, channels
input sound goes below the threshold. will be automatically muted and unmuted when SOLO
Range: 10 ms – 1000 ms (default: 10 ms) buttons are used
To set the compressor for a channel, select its Analog X 9 Pan sliders
button (3). Use these to adjust the stereo positions of the signals input
The compressor settings will be shown for the channel to each channel when they are sent to the stereo bus.
selected by its Analog X button (3). Use the mouse to click and drag a pan slider left or right to
adjust the position.
NOTE While dragging the mouse, the value being adjusted is
• If the input is a stereo signal (stereo-linked channel or
shown in its fader level display area (above 0).
master), compression will start and be applied to both
channels when either the left or right input channel exceeds The value is L20 when set all the way to the left, C when set
the threshold level. in the center and R20 when set all the way to the right.
• When the compressor is off, the compressor curve will Setting range: L20 – L1, C (default), R1 – R20 (41 steps
appear but the meters will not be active. total with C at the center and 20 steps to both left and
right.)
3 Analog X buttons A pan slider appears blue when centered (C) and yellow at
When an Analog X button ("X” is the channel number) is on all other positions.
(lit), the equalizer (1) and compressor (2) settings for that
channel will be shown and can be adjusted as desired. NOTE
Off (default): Analog X button unlit • If a pan slider is centered (C), the signal is reduced by 3 dB
and sent to both the left and right channels of the stereo
On: Analog X button lit
bus.
You can only select one channel at a time. Multiple Analog X • Double-click a pan slider to return it to the center (C)
buttons cannot be on at the same time.
position.
When a channel is selected, click a different channel's button • When a pan slider is set to the left end (L20), the signal for
to select that channel. The previously selected channel
that channel is sent only to the left channel of the stereo
button will become unlit, and the newly selected channel
bus. It is not sent to the right channel of the stereo bus.
button will light.
TASCAM US-16x08 15
6 – Using the Settings Panel
• When a pan slider is set to the right end (R20), the signal for • Turn a LINK button off to split a single stereo channel into
that channel is sent only to the right channel of the stereo two mono channels. The settings for each of the mono
bus. It is not sent to the left channel of the stereo bus. channels become as follows.
Analog X-Y: If on when the LINK button is turned off, the
0 Faders and level meters
odd channel stays on, but the even channel turns off. If
Use the faders for each channel to adjust the levels of the
off when the LINK button is turned off, both channels
channel signal sent to the stereo bus. Use the master fader
stay off.
to adjust the master output level.
PHASE: The settings are not changed. The setting of each
The channel level meters show their signal levels. The master
channel stays as it was.
level meters show the levels of the mixed signal.
EQ: The settings of both channels stay the same as the
The fader level display area (bottom of 0) shows the fader combined stereo channel.
gain value.
COMP: The settings of both channels stay the same as the
The channel and master level meters show green bars for combined stereo channel.
values less than −12 dB, yellow bars for −12 dB to −6 dB, and
red bars for values greater than −6 dB. SOLO: If on when the LINK button is turned off, this stays
on for both channels. If off when the LINK button is
Each level meter has an overload indicator at its top. turned off, both channels stay off.
Range: +6 dB to −∞ (default: 0 dB) MUTE: If on when the LINK button is turned off, this stays
on for both channels. If off when the LINK button is
NOTE turned off, both channels stay off.
• Using the mouse, drag a fader to adjust its level. Move the
Pan sliders: These stay the same when the LINK button is
fader up to increase the level or down to decrease it.
turned off.
• Double-click a fader to return it to its default (0 dB) position.
Level faders: The settings of both channels stay the same
• The channel meters show the levels before being adjusted as the combined stereo channel.
by the faders. Level meters are not affected by fader adjust-
ments or even their channels being muted. w Track notes
You can input up to six English letters and numbers.
q LINK buttons
Turn a LINK button on to combine two adjacent channels
(odd and even) into a single stereo channel. How to input characters
When stereo link mode is enabled, the buttons, knobs and Click a note area to ready it for input. The cursor will blink.
faders of the two channels are combined. The channel level Then, use the computer keyboard to input characters.
meters are also shown as a stereo pair. After you complete inputting characters, press the Enter key
When linked, the LINK button lights. (Default: off ) on the computer keyboard.
NOTE
When a LINK button is enabled (combining two adjacent
channels as a stereo channel), the settings become as You must press the Enter key on the computer keyboard
follows. after you complete inputting characters to confirm the
input. If you move to a different page from the MIXER page
Analog X: If either the odd or even channel is turned on, without pressing the Enter key, the input characters will be
this turns on. If both the odd and even channels are off, shown, but not saved.
this turns off. In addition, the button name changes to
“Analog X-Y” (“X” is the odd channel number and “Y” is the
even channel number).
PHASE: The settings are not combined. The settings of the
channels do not change.
EQ: The setting of the odd-numbered channel is applied.
COMP: The setting of the odd-numbered channel is
applied.
SOLO: The setting of the odd-numbered channel is
applied.
MUTE: The setting of the odd-numbered channel is
applied.
Pan sliders: The settings are not combined. The setting of
each channel can be set independently.
Level faders: The setting of the odd-numbered channel is
applied.
16 TASCAM US-16x08
6 – Using the Settings Panel
INTERFACE page
88 Windows
2
1
Windows Settings Panel screen
88 Mac OS X
1
Mac Settings Panel screen
The “INTERFACE” page has a unit status area and, on Windows 2 Buffer Size (Windows only)
only, a “Buffer Size” area. The driver for the unit stores the audio input and output
Beneath these areas is an image of the rear panel of the unit that signals transferred to and from the computer temporarily in
you can use to check the layout of the jacks, for example. No a buffer. This buffer size can be adjusted.
settings can be changed on this page. Smaller buffer sizes result in less audio signal delay (latency),
but require high-speed processing by the computer.
If the processing cannot keep up, for example, due to other
1 Status display area system operations, clicking and popping noises might occur
This shows the current status of the unit. and the audio signal might even drop out.
Item displayed Meaning Increasing the buffer size will stabilize operation and
This is the software version used suppress negative effects on audio signals, but the delay in
Software Version audio signals sent to the computer will increase.
by unit.
This is the firmware version used You can use the slider on the panel to adjust the buffer size,
Firmware Version
by the unit.1 according to the use conditions.
Device This is the name of the unit.1 Use the slider to select fixed values that increase from left to
This is the current sampling right (64, 128, 256, 512, 1024 and 2048 samples).
Sample Rate
frequency.2
1 “No Device” is shown when no device is connected.
2 “No ASIO Driver” is shown when an ASIO driver has not been
installed.
TASCAM US-16x08 17
6 – Using the Settings Panel
OUTPUT SETTING page
On the OUTPUT SETTING page, you can visually check the routing of signals output from the LINE OUT 1-8 jacks and select them.
1
Windows̲PC画面
2
Windows Settings Panel screen
1 Output signal selection 2 Output signal routing status
Click a box to the right of a LINE OUT X (“X” is 1–8) label to This shows the connection of the signals with the output
open a pull-down menu with BUS line selection options. jacks as selected in area 1.
Select the signal that you want to output from this menu. • Stereo BUS outputs
Options: COMPUTER 1 – COMPUTER 8, MASTER L/
The signals input through each input jack and by USB
MASTER R
output from the computer are mixed and output in stereo.
For details, see “Block diagrams” on page 31 in this
manual.
• Computer BUS outputs
Select output signals from the Computer BUS (1–8), which
come from DAW software running on the computer, to
output them directly from the desired jacks.
NOTE
The output signals selected for LINE OUT 1 and LINE OUT 2
will also be output from the PHONES (L/R) jack.
18 TASCAM US-16x08
6 – Using the Settings Panel
Settings Panel pull-down menus
The Settings Panel has View and SceneMemory pull-down
menus that can be used to initialize and save settings, for
example.
Mac version
View menu 2. A confirmation message will appear. Click the “OK” button in
This menu includes functions to restore the settings of the the message window to reset the Settings Panel settings to
Settings Panel to their defaults (Initialize), minimize the their default values.
application to the taskbar (Minimize) and close the Settings
Panel (Close).
Windows version
Windows version
Mac version
NOTE
Mac version Click the “Cancel” button to return to the Settings Panel
Initialize without initializing.
Select this to reset all the Settings Panel settings. Using the Initialize function will result in the following
settings.
For details, see “Initializing the Settings Panel settings” on
page 19 in this manual. Page Item Default value
Minimize MIXER EQUALIZER HIGH (GAIN) 0 dB
HIGH (FREQ) 5.0 kHz
Minimize the Settings Panel screen to the taskbar (or
HIGH MID (GAIN) 0 dB
Dock on a Mac).
HIGH MID (FREQ) 1.2 kHz
Close HIGH MID (Q) 1.00
Close the Settings Panel screen and quit the application. LOW MID (GAIN) 0 dB
LOW MID (FREQ) 300 Hz
88 Initializing the Settings Panel settings
LOW MID (Q) 1.00
Select this to reset all the Settings Panel settings. LOW (GAIN) 0 dB
LOW (FREQ) 80 Hz
NOTE LCF OFF
The Windows Buffer Size setting is not restored to the COMPRESSOR THRESHOLD 0 dB
factory default. RATIO 1.0: 1
GAIN 0 dB
CAUTION ATTACK 2 ms
After initializing, you cannot restore the previous settings. RELEASE 10 ms
1. In the menu bar, Click “Initialize” in the View menu PAN C (center)
(Windows/Mac). Channel faders 0 dB
Master fader 0 dB
OUTPUT LINE OUT 1 COMPUTER 1
SETTING LINE OUT 2 COMPUTER 2
LINE OUT 3 COMPUTER 3
LINE OUT 4 COMPUTER 4
LINE OUT 5 COMPUTER 5
LINE OUT 6 COMPUTER 6
LINE OUT 7 COMPUTER 7
Windows version LINE OUT 8 COMPUTER 8
NOTE
• If you turn the unit on without launching the Settings Panel,
the LINE OUT 1-8 output settings will be set to COMPUTER
1–8.
• There is no Settings Panel for iOS devices, so the unit will
operate with its default settings.
TASCAM US-16x08 19
6 – Using the Settings Panel
2. Click “Save” in the submenu to save the current Settings
SceneMemory menu Panel settings to the selected scene memory.
Up to 10 Settings Panel states can be saved as scene
memories.
The SceneMemory menu starts with 10 SceneMemoryX ("X”
being 1–10) memories. Select one of these scene memories
to open a submenu that allows you to Save, Load or Rename
it.
You can also initialize all 10 scene memories at the same
time.
Windows version
Windows version
Mac version
88 Loading Settings Panel settings
You can immediately change the current Settings Panel
settings to settings saved in a scene memory by loading it.
CAUTION
If you load a scene memory, the previous settings cannot be
Mac version restored. If you want to keep the current settings, save them
to a different scene memory.
Save
1. Click the name of the scene memory that you want to load
Use this to save all Settings Panel settings except the on/ in the SceneMemory menu to open the submenu.
off status of the Analog X buttons. For details, see “Saving
Settings Panel settings” on page 20 in this manual. 2. Click “Load” in the submenu to immediately change the
Settings Panel settings to those saved in the scene memory.
Load
Use this to immediately apply settings that have been
saved to the selected scene memory. For details, see
“Loading Settings Panel settings” on page 20 in this
manual.
Rename
Use this to change the name of the scene memory that is
saved. For details, see “Input and output channels in mic
preamp mode” on page 22 in this manual.
88 Saving Settings Panel settings
The current Settings Panel settings can be saved in a scene Windows version
memory.
Ten scene memories can be saved.
CAUTION
Only one set of Settings Panel settings can be saved in each
scene memory. For this reason, saving settings to a scene
memory will erase the previously saved settings.
1. In the menu bar, click the name of a scene memory in the
SceneMemory menu (Windows/Mac) to open the submenu.
Mac version
20 TASCAM US-16x08
6 – Using the Settings Panel
CAUTION 88 Initializing all ten scene memories
Scene memories that you have never saved do not contain You can initialize all scene memories at the same time.
any Settings Panel settings. If you try to load such a scene
memory, the following confirmation message will appear. CAUTION
After resetting, you cannot restore the previous settings.
1. In the menu bar, click “Initialize Memory” in the Scene-
Memory menu (Windows/Mac).
Windows version
Mac version
Windows version
88 Changing a scene memory name
You can change the names of scene memories.
1. From the menu bar, click the name of a scene memory in the
SceneMemory menu (Windows/Mac) to open the submenu.
2. Click “Rename” in the submenu.
Mac version
2. A confirmation message will appear. Click the “OK” button
in the message window to reset the scene memory Settings
Panel settings to their default values.
Windows version
Windows version
Mac version Mac version
3. The following name input window will open. NOTE
Click the “Cancel” button to return to the Settings Panel
without initializing.
Windows version
Mac version
4. After you complete inputting the new name, click the “OK”
button in the window.
TASCAM US-16x08 21
7 – Mic Preamp Mode
Using the unit as a standalone mic
preamp
This unit will operate in mic preamp mode when it is not
connected to a computer by USB.
You can use this unit's mic preamps even when it is not
connected to a computer.
88 Input and output channels in mic preamp mode
In mic preamp mode, the routing of input to output channels is
fixed as follows.
Input Output
IN1 LINE OUT1
IN2 LINE OUT2
IN3 LINE OUT3
IN4 LINE OUT4
IN5 LINE OUT5
IN6 LINE OUT6
IN7 LINE OUT7
IN8 LINE OUT8
You can adjust the input level of each channel using its gain
knob.
NOTE
When shipped from the factory, the LINE OUT 1-2 knob is
set to its minimum value, so no sound will be output from
the LINE OUT 1-2 jacks. When using the unit in mic preamp
mode, set the LINE OUT 1-2 knob to its maximum value.
22 TASCAM US-16x08
8 – Application Guide
In this chapter, we explain how to set some audio applications
for use with this unit.
Windows 7
1. Quit all applications and open the Control Panel from the
88 DAW software
Start button menu.
The ways that settings are made differ among DAWs. 2. Open “Sound”.
When using a DAW software, consult its operation manual.
NOTE
If you do not see this item, click Hardware and Sound.
Windows Media Player
Windows 8 3. On the Playback page, right-click “Speakers TASCAM
US-16x08”, and click “Set as Default Device” in the pop-up
1. Quit all applications and right-click the Start screen to show menu that appears.
the App Bar. Then, click the All apps button to open the
When you do this, the green check mark (4) appears next
Apps screen.
to Speakers TASCAM US-16x08.
NOTE
In Windows 8.1, click the ¡â button that appears at the
bottom left of the Start screen.
2. Click Control Panel.
3. Click “Hardware and Sound", and then open the “Sound”
window.
4. On the Playback page, right-click “Speakers TASCAM
US-16x08", and click “Set as Default Device” in the pop-up
menu that appears.
When you do this, the green check mark (4) appears next
to Speakers TASCAM US-16x08.
NOTE
To use this unit as the recording device, open the Recording
page and use Set as Default Device for Line In TASCAM
US-16x08.
4. After completing the setting, click the OK button.
5. Start Windows Media Player, select an audio file and begin
playback.
NOTE
• If you change the setting while Windows Media Player is
running, the software will not recognize that the device has
been changed. In this case, restart Windows Media Player.
NOTE • If you still cannot hear sound after making the settings and
To use this unit as the recording device, open the Recording completing the procedures above, restart the computer.
page and use Set as Default Device for Line In TASCAM • If you make this setting, sound will be output through this
US-16x08.
unit, but no sound will be output by the computer’s speakers
5. After completing the setting, click the “OK” button. or headphone jack.
6. Launch Windows Media Player, select an audio file and start
playback.
NOTE
• If you change the setting while Windows Media Player is
running, the software will not recognize that the device has
been changed. In this case, restart Windows Media Player.
• If you still cannot hear sound after making the settings and
completing the procedures above, restart the computer.
• If you make this setting, sound will be output through
this unit, but no sound will be output from the computer’s
speakers or headphone jack.
TASCAM US-16x08 23
8 – Application Guide
Mac OS X and iTunes
1. Open the Utilities folder within the “Applications folder”,
and double-click “Audio MIDI Setup”. Then open the “Audio
Devices” window.
2. Click “US-16x08” to select it and right-click or control-click it.
Then, click “Use this device for sound output” in the pop-up
menu.
The speaker mark appears next to US-16x08.
NOTE
To use this device as the recording device, select “Use this
device for sound input” for the “US-16x08”.
3. Launch iTunes, select an audio file and start playback.
iOS
No settings are necessary to use this unit with an iOS device.
You can use it right away after connecting to the device by
USB.
NOTE
Connecting headphones, for example, to the headphone
jack of the iOS device will interrupt USB communication
with this unit.
24 TASCAM US-16x08
9 – MIDI Implementation Chart
88 MIDI Implementation Chart
Function Transmit Recognize Remarks
When power on × ×
Basic channels Thru
Settable × ×
When power on × ×
Mode Messages × × Thru
Altered ....................
Note number Range × × Thru
Note on × ×
Velocity Thru
Note off × ×
Polyphonic × ×
Aftertouch Thru
Channel × ×
Pitch bend × × Thru
Control change × × Thru
× ×
Program change Thru
Settable range # ....................
System exclusive × × Thru
Position × ×
System common Song select × × Thru
Tune × ×
Clock × ×
System real-time Thru
Command × ×
Local on/off × ×
All notes off × ×
Other Thru
Active sense × ×
Reset × ×
Notes
Mode 1: OMNI ON, POLY Mode 2: OMNI ON, MONO ˜: YES
Mode 3: OMNI OFF, POLY Mode 4: OMNI OFF, MONO ×: NO
TASCAM US-16x08 25
10 – Troubleshooting
Depending on the application that you are using, you might
Troubleshooting need to make additional device settings.
In particular, DAW applications operate using audio engines
Please read this chapter if you are unable to use the unit with settings that are different from the OS settings, so first
properly even after setting it up following the procedures in this confirm the DAW settings after installing the driver and
manual. Settings Panel for this unit.
If you are still unable to resolve a problem, please contact a Please see the manuals for the applications that you are
TASCAM customer center (see back of document) with the using for detailed setting procedures.
following information about the operating environment and
details about the trouble. 88 Sound breaks up or there is noise.
Operating environment The processing load on the computer causes sound to break up
• Computer manufacturer: and noise to occur.
• Model: Here are some methods to reduce the load on the computer.
• CPU: 1. A wireless LAN and software running in the background,
• Memory (RAM): including antivirus software, regularly put processing
• Operating system: loads on the computer, which can cause sound to break up
and other noise. Stop wireless LAN transmission, antivirus
• Applications used: software and other software running in the background
• Antivirus software: when using this unit.
• Wireless LAN use: 2. Set the buffer size (latency) in the audio application that you
See the end of this document for contact information. are using or in this unit's Settings Panel to a larger value.
(Windows only)
88 Installation fails.
NOTE
88 Installation completes, but the computer does not Consult the maker of the audio application that you are
recognize the unit. using for methods to reduce its load on your computer.
If some trouble is causing installation to fail, or if the computer 3. Change the settings of your computer so that they are
does not recognize the unit even though installation completes, optimal for audio processing.
check the following. Windows 8
1. Change the USB port 1 In Windows 8, right-click the ordinary Start screen
Since the unit might not properly function with some (Metro user interface screen) and then click “All apps”.
USB ports, try connecting to a different USB port that is 2 Right-click “Computer” and select “Properties”.
built into the computer, and reinstall the driver.
3 Click “Advanced system settings”.
NOTE 4 Click “Settings” in the “Performance” section of the
• Try again after disconnecting other USB devices. (Keyboards “Advanced” tab of the “System Properties” window.
and mice can be left connected.) 5 In the “Visual Effects” tab of the “Performance Options”
• Do not use a USB hub. Always connect the unit directly to a window, select “Adjust for best performance”.
USB port on the computer (built-in). Windows 7
2. Stop software that is running in the background a) Turn Aero off.
Since antivirus software and other software running in 1 Right-click the desktop and select “Personalize”.
the background can interfere with installation, stop them
2 Select a “Basic” or “High Contrast” theme.
before beginning installation. See “Installing the driver
and Settings Panel” on page 6 in this manual for how b) Performance settings
to install and uninstall the driver and Settings Panel. 1 Right-click “Computer” and select “Properties”.
88 There is no sound even when audio is playing back. 2 Click “Advanced system settings”.
3 Click “Settings” in the “Performance” section of the
The audio output must be set on the computer. “Advanced” tab of the “System Properties” window.
Please confirm the following while the unit is connected to the 4 In the “Visual Effects” tab of the “Performance Options”
computer. Moreover, if you make the following settings, sound window, select “Adjust for best performance”.
will be output through this unit, but no sound will be output by
the computer’s speakers or headphone jack. Mac OS X
Windows 8/Windows 7 1 Open “System Preferences…” from the Apple menu,
and select “Energy Saver”.
iiSee the “Windows 8” or “Windows 7” instructions in the
“Windows Media Player” section of the “Application guide” 2 Set “Computer sleep” to “Never”.
chapter of the Reference Manual, and make settings as 3 Set “Display sleep” to “Never”.
necessary for the OS.
iiConduct procedures 1-4 for Windows 8 or procedures 1-3 for NOTE
Windows 7 to set the default device for playback. Depending on the Mac OS X version and Mac computer
model, this setting might not be available.
Mac OS X 4. Change the USB port
Quit all applications and open “System Preferences…” from
the Apple menu. Since the unit might not properly function with some
USB ports, try connecting to a different USB port that is
Open “Sound", and select “US-16x08” on the Output tab. built into the computer.
After completing the setting, restart the computer and
check the sound of playback.
26 TASCAM US-16x08
10 – Troubleshooting
NOTE
• Try again after disconnecting other USB devices. (Keyboards
and mice can be left connected.)
• Do not use a USB hub. Always connect the unit directly to a
USB port on the computer (built-in).
TASCAM US-16x08 27
11 – Specifications
88 LINE IN 11-16 line inputs (unbalanced)
Specifications
(LEVEL switch set to “−10dBV")
Connectors: 6.3mm (1/4") standard TS jacks
Ratings (Tip: HOT, Sleeve: GND)
Input impedance: 10 kΩ
88 Sampling frequencies Nominal input level: −10 dBV (0.3162 Vrms)
44.1/48/88.2/96 kHz Maximum input level: +10 dBV (3.162 Vrms)
88 Quantization bit depth 88 LINE IN 11-16 line inputs (balanced)
16-bit or 24-bit (LEVEL switch set to “+4dBu")
Connectors: 6.3mm (1/4") standard TRS jacks
(Tip: HOT, Ring: COLD, Sleeve: GND)
Analog inputs
Input impedance: 10 kΩ
88 IN 1-8 mic inputs (balanced) Nominal input level: +4 dBu (1.228 Vrms)
Connector: XLR-3-31 equivalent Maximum input level: +24 dBu (12.282 Vrms)
(1: GND, 2: HOT, 3: COLD)
Input impedance: 2.4 kΩ Analog outputs
Nominal input level: −68 dBu (0.0003 Vrms)
(gain knob at maximum) 88 LINE OUT 1-8 line outputs (balanced)
Nominal input level: −12 dBu (0.195 Vrms) Connectors: 6.3mm (1/4") standard TRS jacks
(gain knob at minimum) (Tip: HOT, Ring: COLD, Sleeve: GND)
Maximum input level: +8 dBu (1.947 Vrms) Output impedance: 100 Ω
Gain range: 56 dB Nominal output level: +4 dBu (1.228 Vrms)
88 IN 9-10 instrument inputs (unbalanced) Maximum output level: +24 dBu (12.277 Vrms)
(LINE/INST switch set to INST) 88 PHONES output
Connectors: 6.3mm (1/4") standard TS jacks Connector: 6.3mm (1/4") standard stereo jack
(Tip: HOT, Sleeve: GND) Maximum output: 70 mW + 70 mW
Input impedance: 1 MΩ or more (THD+N 1% or less, into 32 Ω load)
Nominal input level: −57 dBV (0.0014 Vrms) 88 Frequency response
(gain knob at maximum)
88 Input w PHONES output
Nominal input level: −12 dBV (0.251 Vrms)
(gain knob at minimum) At 44.1 kHz and 48 kHz
Maximum input level: +8 dBV (2.512 Vrms) 20 Hz – 20 kHz: ±1.0 dB (JEITA), supports Hi-Res
Gain range: 45 dB At 88.2kHz and 96kHz
20 Hz – 40 kHz: ±2.0 dB (JEITA), supports Hi-Res
88 IN 9-10 line inputs (balanced)
(LINE/INST switch set to LINE)
Control input/output ratings
Connectors: 6.3mm (1/4") standard TRS jacks
(Tip: HOT, Ring: COLD, Sleeve: GND) 88 MIDI IN connector
Input impedance: 10 kΩ Connector: 5-pin DIN
Nominal input level: −41 dBu (0.0069 Vrms) Format: standard MIDI
(gain knob at maximum)
88 MIDI OUT connector
Nominal input level: +4 dBu (1.228 Vrms)
(gain knob at minimum) Connector: 5-pin DIN
Maximum input level: +24 dBu (12.282 Vrms) Format: standard MIDI
Gain range: 45 dB 88 USB
Connector: 4-pin USB B-type
Transfer rate: USB 2.0 High Speed (480 Mbps)
28 TASCAM US-16x08
11 – Specifications
Audio performance Mac OS X
88 Mic amp EIN (equivalent input noise) 88 Supported operating systems
−125 dBu or more OS X Yosemite (10.10 or later)
88 Frequency response OS X Mavericks (10.9.1 or later)
OS X Mountain Lion (10.8.4 or later)
88 Input w LINE OUT (BALANCED)
88 Computer hardware requirements
At 44.1 kHz and 48 kHz
Apple Macintosh computer with a USB 2.0 or USB 3.0 port
20 Hz – 20 kHz: ±0.5 dB (JEITA)
At 88.2kHz and 96kHz 88 CPU/processor speed
20 Hz – 40 kHz: ±0.5 dB (JEITA) 2 GHz or faster dual core processor
88 S/N ratio 88 Memory
100 dB or higher 2 GB or more
(LINE IN w LINE OUT, gain knob at minimum, JEITA) 88 Display resolution
88 Distortion At least 1280x800
0.006% or less
(Mic/LINE IN w LINE OUT, 1kHz sine wave, at nominal input iOS devices
level and maximum output level)
Apple devices running iOS 7 or later
88 Crosstalk
100 dB or higher
(Mic/LINE IN w LINE OUT, 1kHz)
Supported audio drivers
Windows: ASIO2.0, WDM, MIDI
Mac: Core Audio, Core MIDI
Computer system requirements
Check the TEAC Global Site (http://teac-global.com/) for the General
latest information about supported operating systems.
88 Power
Windows Specialized DC12V AC adapter (GPE248-120200-Z)
88 Supported operating systems 88 Power consumption
Windows 8 (including 8.1) 32-bit 12 W
Windows 8 (including 8.1) 64-bit 88 Dimensions (W × H × D)
Windows 7 32-bit SP1 or later
Standard frame attached (state when shipped from factory)
Windows 7 64-bit SP1 or later
445 × 59 × 219 mm
88 Computer hardware requirements Rack mount adapters attached
Windows computer with a USB 2.0 or USB 3.0 port 482.6 × 44 × 218.4 mm
Computer 88 Weight
88 CPU/processor speed 2.8 kg
2 GHz or faster dual core processor (x86) 88 Operating temperature range
88 Memory 5–35°C (32–104°F)
2 GB or more
88 Display resolution
At least 1280x800
CAUTION
Operation of this unit was confirmed using standard
computers that meet the above requirements. This does
not guarantee operation with all computers that meet the
above requirements. Even computers that meet the same
system requirements might have processing capabilities
that differ according to their settings and other operating
conditions
TASCAM US-16x08 29
11 – Specifications
Dimensional drawings
88 Standard frame attached (state when shipped from factory)
PP
PP
PP
PP
PP
88 Rack mount adapters attached
PP
PP
PP
PP
PP
PP
PP
PP
• Illustrations in this manual might differ in part from the actual product.
• The external appearance might be changed without notification to improve the product.
30 TASCAM US-16x08
11 – Specifications
Block diagrams
0,&35($0302'(
$8',2,17(5)$&(02'(
TASCAM US-16x08 31
11 – Specifications
Level diagrams
/(9(/',$*5$0
32 TASCAM US-16x08
TASCAM US-16x08 33
TEAC CORPORATION http://tascam.jp/
Phone: +81-42-356-9143
1-47 Ochiai, Tama-shi, Tokyo 206-8530 Japan
TEAC AMERICA, INC. http://tascam.com/
Phone: +1-323-726-0303
1834 Gage Road, Montebello, California 90640 USA
TEAC MEXICO, S.A. de C.V. http://teacmexico.net/
Phone: +52-55-5010-6000
Río Churubusco 364, Colonia Del Carmen, Delegación Coyoacán, CP 04100, México DF, México
TEAC UK LIMITED http://tascam.eu/
Phone: +44-8451-302511
Meridien House, Ground Floor,69 - 71, Clarendon Road, Watford, Hertfordshire, WD17 1DS, UK
TEAC EUROPE GmbH http://tascam.eu/
Phone: +49-611-71580
Bahnstrasse 12, 65205 Wiesbaden-Erbenheim, Germany
TEAC SALES & TRADING(SHENZHEN) CO., LTD http://tascam.cn/
Phone: +86-755-88311561~2
Room 817, Block A, Hailrun Complex, 6021 Shennan Blvd., Futian District, Shenzhen 518040, China
Texte extrait tel quel de la pièce officielle, qui seule fait foi. La mise en page du document d'origine peut différer.